Click photos to
enlarge.
Ordering information at the bottom of this page
The hardened pin-plates are shown removed. There are two sets
of bolt holes on the jaws that can used for holding down
custom fixtures.
Titan Vise is so large a PalmControl vise will even
fit in its jaws.
Brake screw with 10 turns of adjustment
With a small vise you can hold small items but not large
items as well. With a larger vise you can hold small items
as well as large items. The Titan is precision made
for the most delicate of work. Our ring holders will
even fit the Titan vise. Above photo is the inside
ring holder in the 90lb Titan vise. Visit the
vise accessory page.
for more information about these holders.
Since the jaws are threaded, various fixtures can be made and
bolted down.
The wood jaws shown above were made
for the 6" Goliath Vise and
Turntable vise
but they also fit the smaller of the two bolt patterns on the
Titan Vise.
These wood jaws look small on the Titan but will still work
depending on what
you are holding. They are shown as example ideas for
making your own
larger ones. You may contact us if you have a special
request.
The Vise Holding
Accessory kit
will also fit the Titan with the smaller of the
two bolt patterns at the top of the jaws.
Because the 90lbs ball is difficult to pick up with your hands,
a lifting plate and handle is included. View the page
link below for more information about
this and how to uncrate the vise when it arrives. Instructions
- Uncrating the 90lb TITAN Engraving Vise
90lb.
Titan Engraving
Vise™ Features:
*Stainless steel
construction
*Jaws,
pin-plates and lead screw are hardened stainless
*3/4" diameter acme lead screw
*Precision machined
*Adjustable friction drag
*Pin-plates have pin holes with a
smaller hole through the plate for ease of cleaning out pin
holes. *Two sets of threaded holes in jaws accept
pin-plates or custom fixtures
*8"
Body Diameter
*9"
Base Diameter
*Height
from bottom of base to top of jaws 8.25" (with
pin-plates)
*Jaw
width 4.75"
*Jaw height 3.25" (with pin plate)
*Maximum
jaw opening 4.5"
*Includes pin-plates, pins, base and
wrenches
*Weight
90 lbs. (Shipping weight with crate 102 lbs.)
90lb.
Titan
Ball Vise
$2195
Concerning shipping. Vises ship by FedEx
ground within USA. We have not had good luck with USPS for vises.
Pins for pin-plates
information
The Titan vise ships
with eight hardened 5/8" long pins that will protrude 1/4" above the pin-plates. Purchase
additional pins below.
The pin-plates accept 3/16" diameter
pins. Both hardened and annealed pins are available.
The hardened pins can break off if given enough pressure.
If a pin is snapped off, the
broken pin can easily be removed by removing the two screws that
hold the pin plate down. A small punch can knock the
broken pin out from the back side.
Hardened pins 5/8" long (protrude
approx 0.150" above pin-plates) pack of ten $7.00
3/4" long (protrude
approx 0.275" above pin-plates) pack of ten $8.00
7/8" long (protrude
approx 0.400" above pin-plates) pack of ten $9.00
Annealed steel pins Given enough pressure these will bend rather than
break.
3/4" long (protrude approx 0.275" above pin-plates) pack of ten $11.50
Brass pins Brass is less marring to items being held, however they will
bend and dent more easily than annealed steel pins.
3/4" long (protrude approx 0.275" above pin-plates) pack of ten $26.00
