TrueCenter™ CamLock™ Goliath Sized

TrueCenter® CamLock® Vise
Smooth and Accurate Locating Vise
Keep your engraving location in view and centered

Convert a traditional ball base into a Positioning Vise - Patent pending
Made in Nebraska, USA!

Click photos to enlarge

Above: TrueCenter CamLock vises with Lindsay Goliath ball.
* One hand release & lock.
*Smooth slide positioning.
*Stainless machined. No castings.
* Heat-treated stainless glide plate.
* Low profile reversible, threaded and heat-treated jaws
*Available with two vise jaw options as described in above and below photos.

- Option 1 -

Option 1: Low profile reversal and customizable jaw version. Turn a traditional ball base (any brand) into a TrueCenter CamLock vise. See overview photo at the top of this page labeled option #1.

TrueCenter® CamLock® Option #1
Out of Stock

The TrueCenter CamLock vise is attached to a traditional ball base. Supplied with fasters to fit a Lindsay Goliath. On request other fasters can be custom made for other ball bases - patent pending. This option 1 low profile TrueCenter CamLock vise has a wider opening, with reversible and heat treated stainless jaws. Also, the jaws incorporate threaded holes in the tops and faces for customization. Note, the multi-coin jaws will screw right to the jaws of the TrueCenter CamLock vise. Includes wrenches, 10 pins and instructions.

- Option 2 -

Option 2: Reuse your Lindsay Goliath parts to help save money. See overview photo at the top of this page labeled option #2.

TrueCenter® CamLock® Option #2
Out of Stock

This TrueCenter CamLock vise option 2 is available to utilize and reuse the jaws of a Goliath vise and Goliath ball. Includes fasters for fitting Goliath, wrenches and assembly instructions. See overview photo at the top of this page labeled option #2.

- Option 3 -

This "Option 3" includes the TrueCenter CamLock vise along with the ball base as pictured above.

Option #3 - TrueCenter™ CamLock™ with low profile along with ball base.
Out of Stock

Note: A smaller TrueCenter CamLock vise for use on small ball bases such as the Lindsay PalmControl vise is in the works. The above TrueCenter CamLock vise option #1 could also work on the 90lb Titan base. Contact us if you are interested in a larger version of the TrueCenter CamLock vise for the 90lb Titan.

CamLock® Jaw Plates and Centers

CamLock® Jaw Plates and Centers

These will fit either of the two sizes of CamLock vise jaws (Goliath and PalmControl CamLock). Scroll down to see examples of accessories installed.

CamLock Vise jaw plates and accessories
as pictured above with six finger Cosmos collet $135

CamLock Vise jaw plates and accessories
as pictured above with twelve finger Cosmos collet $147

Purchase separately
Jaw Plate A $41
Jaw Plate B $38
Centers Long $14
Centers Short $12
Cosmos Collet brass 6 fingers $25
Cosmos Collet brass 12 fingers $35
Nylon Washers $3

Tip Link: How to center the TrueCenter CamLock vise under your microscope

Photos and Videos

TrueCenter CamLock on 90lb Titan Vise

TrueCenter CamLock on an early Low Profile Dovetail Vise

TrueCenter CamLock on an older Ray Letourneau Vise

Mike Dubber engraving - TrueCenter CamLock in Mike's 90lb Titan vise.
Mike has written a review on the engraving forum - link

Engraving Vises home page